Manual Chapter :
Best Practices
Applies To:
Show Versions
BIG-IP AAM
- 15.1.9, 15.1.8, 15.1.7, 15.1.6, 15.1.5, 15.1.4, 15.1.3, 15.1.2, 15.1.1, 15.1.0, 15.0.1, 15.0.0, 14.1.5, 14.1.4, 14.1.3, 14.1.2, 14.1.0, 14.0.1, 14.0.0
BIG-IP APM
- 17.1.1, 17.1.0, 17.0.0, 16.1.4, 16.1.3, 16.1.2, 16.1.1, 16.1.0, 16.0.1, 16.0.0, 15.1.9, 15.1.8, 15.1.7, 15.1.6, 15.1.5, 15.1.4, 15.1.3, 15.1.2, 15.1.1, 15.1.0, 15.0.1, 15.0.0, 14.1.5, 14.1.4, 14.1.3, 14.1.2, 14.1.0, 14.0.1, 14.0.0
BIG-IP LTM
- 17.1.1, 17.1.0, 17.0.0, 16.1.4, 16.1.3, 16.1.2, 16.1.1, 16.1.0, 16.0.1, 16.0.0, 15.1.9, 15.1.8, 15.1.7, 15.1.6, 15.1.5, 15.1.4, 15.1.3, 15.1.2, 15.1.1, 15.1.0, 15.0.1, 15.0.0, 14.1.5, 14.1.4, 14.1.3, 14.1.2, 14.1.0, 14.0.1, 14.0.0
BIG-IP AFM
- 17.1.1, 17.1.0, 17.0.0, 16.1.4, 16.1.3, 16.1.2, 16.1.1, 16.1.0, 16.0.1, 16.0.0, 15.1.9, 15.1.8, 15.1.7, 15.1.6, 15.1.5, 15.1.4, 15.1.3, 15.1.2, 15.1.1, 15.1.0, 15.0.1, 15.0.0, 14.1.5, 14.1.4, 14.1.3, 14.1.2, 14.1.0, 14.0.1, 14.0.0
BIG-IP DNS
- 17.1.1, 17.1.0, 17.0.0, 16.1.4, 16.1.3, 16.1.2, 16.1.1, 16.1.0, 16.0.1, 16.0.0, 15.1.9, 15.1.8, 15.1.7, 15.1.6, 15.1.5, 15.1.4, 15.1.3, 15.1.2, 15.1.1, 15.1.0, 15.0.1, 15.0.0, 14.1.5, 14.1.4, 14.1.3, 14.1.2, 14.1.0, 14.0.1, 14.0.0
BIG-IP ASM
- 17.1.1, 17.1.0, 17.0.0, 16.1.4, 16.1.3, 16.1.2, 16.1.1, 16.1.0, 16.0.1, 16.0.0, 15.1.9, 15.1.8, 15.1.7, 15.1.6, 15.1.5, 15.1.4, 15.1.3, 15.1.2, 15.1.1, 15.1.0, 15.0.1, 15.0.0, 14.1.5, 14.1.4, 14.1.3, 14.1.2, 14.1.0, 14.0.1, 14.0.0
Best Practices
vCMP best practices
F5 Networks makes the following recommendations for managing a vCMP system.
Category |
Recommendation |
|---|---|
vCMP disk management |
Ensure that you allocate enough disk space for other installation slots for the vCMP host before you
provision the vCMP feature. |
Network setup |
Before setting up a vCMP system, verify that each slot's management interface is
physically wired to an external bridge. |
Change of vCMP management IP address |
You should only change the vCMP management IP address when logged into the vCMP
host. Changing this address when logged into a guest could produce unexpected results.
Note that changing individual cluster member IP addresses when logged into a guest is
fully supported. |
Slot assignment to guests |
Whenever possible, configure a guest to allow the guest to run on more slots than
are actually populated with blades. The result is an automatic expansion of the guest
cluster when you insert an additional blade. |
Virtual disk management |
To prevent unattached virtual disks from consuming disk space over time, consider
deleting unwanted virtual disks from the system. Otherwise, previously provisioned
virtual disks remain on disk after their associated vCMP guest configurations have
been deleted. |
Protection from performance degradation |
To protect a guest from performance degradation if a blade failure occurs,
configure high availability if possible. You do this by setting up device service
clustering (DSC). For a standalone vCMP system, consider
deploying guests with sufficient cores and slots to ensure that a single blade failure
does not result in unacceptable service degradation. |
Adjusting the MTU size for a guest |
When a guest is subscribing to a host-based VLAN, you should only adjust the
VLAN's MTU size when you are logged into the guest. Changing the MTU size when logged
into the host has no effect on the guest's ability to process traffic or manage
routing. |
